The StandStrong is a brand new, one of a kind, strength training device, designed to help you squat more weight today.
The StandStrong helps with 3 things:
*OVERLOAD training by allowing you to do more reps, sets, and heavier weight to gain strength
*EMPOWER you to to squat more by offering more support at the most difficult portion of the movement.
*PROTECT you by reinforcing proper form and technique to help prevent injury
How Do I Put It On?
WHICH STANDSTRONG IS FOR ME?
-
StandStrong Original
-
The StandStrong Original is designed to be used with any standard lifting belt. The sleek design allows you to slide it right onto your personal lifting belt.
-
Why is that important?
-
The same fit you are used to with your personal lifting belt
-
The same support you are used to with your personal lifting belt
-
Can be more 'heavy duty' than the StandStrong Flex
-
Easily swapped from one belt to the next
-
-
-
-
StandStrong Flex
-
The StandStrong Flex is designed to be worn in the absence of a standard lifting belt. The lightweight design is NOT intended to be a fully supportive lifting belt in and of itself, but just enough to give the wearer the flexibility to use it on various exercises.
-
Why is that Important?
-
Good for people that dont normally wear a lifting belt
-
Less constrictive than a standard lifting belt
-
Good for certain lower body exercises in which you may not wear a standard lifting belt
-
Good for beginners in the gym
-
-
-
SIZING THE ORIGINAL?
The StandStrong Original comes in two sizes; 4 inch and 6 inch. These sizes correlate to the width of your personal lifting belt. Most standard lifting belts are either 4 inches all the way around, or have a larger 6 inch section on the back of the belt. Since the Stand Strong Original will sit at the center of your back during use, make sure to pick the size that matches the width at the back of your belt.
The 4 inch and the 6 inch models are each sized with a maximum belt thickness of 13mm. If your belt is thicker than 13mm then the StandStrong Original may not fit on your belt.
SIZING THE FLEX?
The StandStrong Original comes in two sizes; 4 inch and 6 inch. These sizes correlate to the width of your personal lifting belt. Most standard lifting belts are either 4 inches all the way around, or have a larger 6 inch section on the back of the belt. Since the Stand Strong Original will sit at the center of your back during use, make sure to pick the size that matches the width at the back of your belt.
The 4 inch and the 6 inch models are each sized with a maximum belt thickness of 13mm. If your belt is thicker than 13mm then the StandStrong Original may not fit on your belt.
PROPER MAINTENANCE?
Proper maintenance of your StandStrong is important for it's longevity.
Wash regularly by hand.
Do not store it with sharp objects.
Do not overstretch your StandStrong.
Only wear your StandStrong for it's intended use
HOW DO I WEAR THIS?
StandStrong Flex: Wear the waistband the same way that you would any standard weightlifting belt.
StandStrong Original: Slide your standard weightlifting belt through the belt loop so that the Stand Strong sits at the center of your back
Leg loops (on both models): Have the loops sit between your waist and knee, usually just above the knee at the base of the quad. (For taller people or people with long femurs, the leg loop may rest higher on the leg, and vice versa for short people or people with shorter femurs)
Point the finger loops on the front of leg loops outward about 45 degrees, and make sure the point at which the vertical elastic bands attach to the leg loops is on the inside of the back of your legs. This will decrease the likelihood that the bands of the StandStrong will jut out during use.
WEAR AND TEAR?
The StandStrong is hand made with high quality materials but, if you notice any rips, tears, or structural damage to your StandStrong do not use it. This could result in personal injury. Stand Strong Company, LLC. is not liable for any injuries incurred while wearing a StandStrong, damaged or otherwise.